Search Results for ‘r380’

I have a great running 2.5NA engine that was just pulled from my '95 Ex-MoD. Engine drove strong and cruised at 55mph with left over room to pass (that's right, I would even sometimes pass SLOWER cars) at 62mph! Most of the ancillaries will be included (I do plan to keep the starter as a spare...

Hey gang, I've got an all original 3.5 v8 in my '83 110. It's about time for a major refresh, likely main bearings, a serious carb rebuild (or likely a holley/edelbrock setup), and a full refresh of the top end. Additionally, my clutch is about to go, so that needs to be done too. I'm not sure I...

My fault for not specifying which would get exactly which parts if separated, so now for sale as a unit. Selling together R380 and 1.2 ration LT230. Both in good working order. Would much prefer local pickup in either Long Island (Southold, NY) or New York City but could arrange...

I need to replace the failing LT77 on my Exmod 110 and sourcing a proper one is looking to be very difficult, so looks like I'm headed the route of an R380 upgrade. Figured I'd touch base on here to see if I can find a good quality R380 short before I start throwing money at Ashcroft. Anyone...

Got some inquiries on the subject so it seems pertinent to post a parts list with an installation post to follow. My truck is a 300TDI with a long bell-housing R380 (not stumpy) but the parts below should be identical. 200TDI vehicles should share the same clutch fork arm and throwout bearing...

Hey ya'll, I'm new to the forums but have a truck to sell so I thought I would post it up here for the first time. I have a 1985 Defender 90 that's clean and ready to go. It's up in Minneapolis on Craigslist here: minneapolis.craigslist.org/hnp/cto/d/land-rover-defender/6588514708.html Basic...

I've had this stashed away for a personal project for some time but will not use it. Removed from a 300Tdi Discovery, shipped here as part of a swap kit. I have not personally run it but it seems good. This would fit a 300Tdi Defender by changing the shifter. $500 for both, pickup only. Adam

Looking for an R380 tunnel. Any available?

I'm looking for a R380 tunnel and/or a seatbox box adapter. I know Doug aka Uncle Douglas is working on getting these made but he is still a couple weeks away from completion. This is for a automatic conversion. I thought I could get away with the LT85 tunnel since it is similar but the fit is...

https://tucson.craigslist.org/pts/d/land-rover-turbo-diesel/6552927743.html I met the seller and chatted about the engine. I saw a video of it seeming to run very well. He pulled it to do an LS swap. The seller can be contacted through the Craigslist Ad, he's not a member here. Seems like a...

Please let me know what you have new or good used is fine. Regards, David

I never drive my rover. Have barely touched it since I put a new clutch in last year. Always take the UNIMOG instead... It is a South Carolina truck. Not rusted out. Has about 150k on the body and 50k on the engine. 6k on the gearbox and redone transfer case. Gearbox is from Ashcroft. It...

Bearmach brand. $80 shipped CONUS

FS is a new R380 Stumpy with heavy duty clutch fork and all the other parts including the release bearing (not in picture). We bought this from Ashcroft a while ago and decided to use an automatic with a 300TDI. $2,700 + Shipping Fastenal in USA or by your arrangements. We will crate and drop...

So I fired up my motor for the first time, ran great but it was pissing trans oil from the bellhousing. Like streaming not just a drop The trans is a rebuilt r380. I pulled it out this am and popped off the front cover. Once I took the bottom two bolts of the front cover order it started...

I've done a bit of searching and can't seem to find the answer to this question. I am swapping my old LT77 from my 1993 D90 with a shorty R380 from Ashcroft. The D90 is my daily driver and would rather it not be out of commission for an extended period of time. Has anyone here done this? Any...

I have a 109 in the shop that was fitted with a 200TDi and a Series 4 speed. The transmission had seen better days, but was a running and driving, functioning set-up. Decided to go with an Ashcroft R380 mated to the Series t-case. Problem I have is that I have almost no friction on the disc...

$50 plus shipping

$75 shipped within CONUS.

Replace your broken plate. $20 shipped within CONUS.