For all you owners of DI's, DII's or 1995 SWB RRC's I have a nice rear driveshaft with four bolt flanges at both ends. I can sell that along with the rear diff four bolt flange and spacer to enable conversion from a rotoflex rear to a four bolt flange rear.
Superior Superflex Radius Arms Landrover Defender/Discovery/Rangerover Offroad Series 2 Inch Lift
Anyone Seen these before?
Looks like another take on the hinged radius arm, but without the removable pin?
The Science Behind Superflex Arms
Discussion on Aussie Land Rover Board...
I'm looking for a pair of the flex fuel lines for a '95 d90 NAS (not diesel)
It looks like the two are identical with Threaded ends...lines are located above the tank and come from the fuel pump.
New ones are crimped to the fuel lines and i dont need to replace if possible.
I want to purchase the X-Deflex rear anti-sway bar from foundry4x4 . It is designed to fit the 110. The Fuel tank on a NAS 90 and TD5 90 hang much lower and required modification.
I have a 4" lift and 35's on my 2000 TD5 90. What are the modifications/additions I need to do? In 1 year I will...
A powerful F-16-1800 30 Watt Flexible solar panel. Includes the Morningstar charge controller so your batteries will not be boiled off by over-charging. Has a female 12 V socket adaptor to connect any 12 Volt goodie that can hook up to a car, like USB chargers, inverters, whatever. Also has a...
I'm trying to find a flexplate, buttress ring and bolts from a disco 1 or range rover classic with a 3.9 v8.
I'll need to confirm bolt pattern so please be prepared to take a few simple measurements :) (something no ebay seller seems willing to do :/ )
I'm trying to figure out what flexplate I need before I start buying things sight unseen through ebay etc.
I'm looking to match up to my marks4WD crank adapter but I cant seem to wrangle a straight answer out of them as to what particular part number I should be looking for.
$350 plus shipping (located in NJ). less than 1000 miles on the system. we even added line-x for added rust protection.
Production Land Rovers compromise by fitting a weak anti-roll bar which improves the handling a bit and doesn`t limit the off road capability too much. The standard bars only...
I'm installing vented rotors and the bigger 110 calipers on my DI with Ferodo FDB871 pads. I figure I'll have to fab up some hard lines from the caliper to the swivel housing bracket (unless there is a direct fit?). Also, I want to use s/s flex hoses. Do I just go with the DI pieces or is there...
My refresh has hit a road block...has anyone here installed a X Deflex Anti Roll Bar on a "NASD90".
The tank on a NAS is lower than an 110 and a pre-TD5 ROW 90. Need some help on this...
I know Wolf did his 110 but the 90 appears to be different...significantly.
Never installed, going a different direction. Just the 4 flares.
Purchased from Lucky8 for $298 + shipping.
"NOW 75mm WIDE!!!Flexi Flares are specially formed wheel arch extensions that enable the cutting of fenders in order to fit larger tires and gain maximum articulation. These flexi arches...
Had this mounted on the passenger wing top and attached to my exo-cage, made from 3" st/st tube powder coated gloss black. Comes with Safari snorkel top & length of flex pipe that fits a RRC air box. Will need some brackets making to attach to cage etc
$250 + S&H
Anyone know where I can get this kind of snorkel hose with the proper hose-end cuffs (this one is by Masai and has a length of 300mm or about 12 inches) but in a 16-inch length (or thereabouts) with a 2.75 or 3.00 inch inner diameter?
my long hose for my NAS mantec ended up with a hole in it after laying on my exhaust downpipe. want to shorten and tighten up the intake section with intake pipe, but need another short section (12-18") for my filter assembly end.
anyone have a good one with no holes laying around? need my...
a section of my mantec hose, which was too long to begin with, wore a hole in the tubing from being too close to my turbo. need to replace with a shorter section. 3' would be perfect. I'm looking for the reinforced cuffed kind that makes a waterproof seal on both ends.