Defender Source Forum banner
bracket
1-20 of 395 Results
Advanced
  1. Wanted
    I have the mounting hardware but I can't find the bracket. If you know where to find one or have one you'd be willing to sell, please send me a note.
  2. Defender Technical Discussions
    I can not seem to locate the part number in the LR workshop pages for the rear seat support brackets that mount on the sloped part of the wheel well. Picture attached with red arrow pointing to the part - 2007+ model year rear tub. I need both right and left side. Thanks
  3. For Sale - Parts
    Defender 200TDi air cleaner and it's bracket. Missing the rubber valve and it's clip. $450+shipping located in Portland, ME
  4. Wanted
    Searching for the OEM crossbar brackets that clamp to the roll cage. Needing 2 pair.
  5. Wanted
    Anyone have one or know what works. Let me know
  6. Wanted
    I'm looking for a PS pump bracket for 200tdi - PN ERR1976. I found that my new motor was incorrectly fitted with PN ERR2605 which rotates the pump so the hoses don't come close to fitting (bracket on the right). The bracket on the left is ERR1976.
  7. Defender Technical Discussions
    Hi there, My Google-fu is exhausted :icon_peace: I'm looking to purchase the wolf style rear bench seats, part number EXT057-DGV which I'm intending to retrofit into a 1992 MoD Defender 90 (non-wolf). From what I've seen there is a bracket/mounting plate that sits behind the seat for correct...
  8. Wanted
    Chassis bracket for steering box and panhard rod mounting for LHD NTC9461 anyone got these laying around. Looking for 2.
  9. For Sale - Parts
    Pretty much what RN sells for $989 (PLH61990NASHD). The rear crossmember isn't aligned perfectly; one side tilts downwards a little bit. I drilled a new hole in the fuel tank cradle brackets because of that to fit the NAS bumper lower mounting arms. Also, the galvanizing is cracked a little on...
  10. For Sale - Parts
    PS bracket for a 2.5na. $150 shipped. Includes the cast bracket for the alt and the mounting plate for the PS pump.
  11. Defender Technical Discussions
    I need to repair one of my sidewalls. I have one rotted bottom corner bracket on the sidewall. This is the attachment point to the back corner of the tub. I did not see a replacement on the YRM site and was wondering if anyone knew of a place to get it before I start trying to fabricate one...
  12. For Sale - Parts
    I have a known good operating condition LR 300 tdi a/c compressor and the compressor mount I removed from a factory original setup yesterday. $200
  13. Smaller Projects
    I recently purchased a new Mantec Spare Tire Carrier and it didn't come with the three hinge backing plates. For clarification, I am talking about the backing plates go on the inside of the body capping and the rear crossmember that hold the swing away porting to the truck. The pictures on the...
  14. Wanted
    Looking for A-bar with light bracket for my '97 D90 NAS similar to the one in the photo below. PM me if you have one for sale. Thanks!
  15. Defender Technical Discussions
    So I have a rebuilt 300 TDi without the air cleaner bracket for a defender installed. The shop that rebuilt it, said to just remove the two head bolts, install the bracket and retorque the two bolts. Has anyone done this before with or without issues? It makes me nervous to not retorque them all.
  16. Wanted
    Does anyone have a NTC1201 or ANR4657 laying around? Thanks Looks like this, #4 in the picture
  17. For Sale - Parts
    Rear bench with all the seat belts and brackets. plastic housing on one of the female buckes has broken off. includes all brackets and all belts. $500 plus shipping
  18. Wanted
    Looking to put power steering on my /87 Tithonus. Any one have the parts? 2.5NA 12J Pump #'s ETC9077, NTC8297, NTC9070 bracket ERC6974, ETC8854 plate ERR1976, ERR2605
  19. For Sale - Parts
    $199 + shipping. Only 1 has the seat belts. Bought for a project and never used them.
  20. Wanted
    NTC9461 anyone got one laying around?
1-20 of 395 Results
Top